Snow Rider has all the accessories you need to enjoy winter. From the tiny tot to the seasoned veteran, our team can find you the gear you need to stay safe and warm on the slopes.
End Of Season Blowout Sale!
From now until the end of the season (March 24), save 30% off ALL gear and merch at Snow Rider. (Season Pass Holders save 35%.)
Note: Sale applies to goods only, not services. For any questions, please contact our Snow Rider team at 780-434-3991.
Snow Valley’s Service Shop can service most equipment. Our trained technicians can perform minor or major tunes on your equipment plus many other services including sharpening, binding installation or mount, stance adjust and wax.
Snow Valley's Snow Rider Ski Shop also features a Wintersteiger 'Speedtronic' Ski Binding Setting and Testing Machine. This machine will test the tolerances of your bindings to ensure their safe and consistent operation based on your personal settings. You will also receive a detailed computer printout of the results.
Pass Holder: $55
Non-Pass Holder: $65
Maintenance for skis with base gouges
Clean and stone grind base, P-Tex gouges, ceramic-disk sharpen side and base edges, detune, wax & buff
Pass Holder: $45
Non-Pass Holder: $55
Maintenance for skis in good condition
Clean and stone grind base, ceramic-disk sharpen side and base edges, detune, wax & buff
Pass Holder: $30
Non-Pass Holder: $35
Clean base, sharpen side edges, detune, wax & buff
Recommend after every 5-10 uses, or before a trip to the mountains
Clean base, wax & buff.
Fully transferrable, 5 full ski or snowboard waxes: Clean base, wax & buff.
New binding mount OR
binding re-mount: remove binding from ski, fill and seal holes, remount binding
* Note: Not all bindings can be remounted on all skis. Also, Snow Rider cannot remount bindings that are no longer indemnified by the manufacturer; bindings that have surpassed their indemnification period will not be accepted for service work. Please ask our staff if unsure.
New binding mount OR
binding re-mount: remove binding from ski, fill and seal holes, remount binding
* Note: Not all bindings can be remounted on all skis. Also, Snow Rider cannot remount bindings that are no longer indemnified by the manufacturer; bindings that have surpassed their indemnification period will not be accepted for service work. Please ask our staff if unsure.
Adjust binding to boot, set release value (DIN) to correct position (according to height, weight, skier ability, boot sole length)
* Note: Not all bindings can be adjusted to fit certain boots. Remount may be required in some situations. Not all bindings can be remounted on all skis. Also, Snow Rider cannot remount bindings that are no longer indemnified by the manufacturer; bindings that have surpassed their indemnification period will not be accepted for service work. Please ask our staff if unsure.
This process uses specialized equipment to check the release values of your binding to make sure that they are within a safe operating range. The technician will also check your ski boot/binding interface to ensure proper release and retention functions.
Pass Holder: $55
Non-Pass Holder: $65
Maintenance for boards with base gouges
Clean and stone grind base, P-Tex gouges, ceramic-disk sharpen side and base edges, detune, wax & buff
Pass Holder: $45
Non-Pass Holder: $55
Maintenance for skis in good condition
Clean and stone grind base, ceramic-disk sharpen side and base edges, detune, wax & buff
Pass Holder: $30
Non-Pass Holder: $35
Clean base, sharpen side edges, detune, wax & buff
Recommend after every 5-10 uses, or before a trip to the mountains
Clean base, wax & buff
Fully transferrable, 5 full ski or snowboard waxes: Clean base, wax & buff.
Mount new binding to board
Re-mount old binding
Change Stance
Adjust to boots for correct fit
Due to the efficiency and waste reduction of our Wintersteiger WaxJet, there will be an additional charge for an iron wax. Please inform the technician at the time of drop off if you wish to use this service.
If you require any more information, please call Snow Rider @ 780-434-3991 ext. 249 or visit the Shop located behind Guest Services.
Other Repairs will be handled at the discretion of the technician.
Glue top sheet back on
24 hour drying time required
Sharpen Only: $15
P-tex work: $20
Base Grind / Texturing: $20
The Turnaround time for all equipment is 48 hours.
Pick-up tab must be present in order to pick up equipment.
For Binding Adjustments, binding mounts, and binding inspections you need to bring in ONE boot. Please know the height, weight and skier type for these services.
Snow Rider cannot adjust bindings that are no longer indemnified by the manufacturer; bindings that have surpassed their indemnification period will not be accepted for service work.
Pass Holder: $55
Non-Pass Holder: $65
Maintenance for skis with base gouges
Clean and stone grind base, P-Tex gouges, ceramic-disk sharpen side and base edges, detune, wax & buff
Pass Holder: $45
Non-Pass Holder: $55
Maintenance for skis in good condition
Clean and stone grind base, ceramic-disk sharpen side and base edges, detune, wax & buff
Pass Holder: $30
Non-Pass Holder: $35
Clean base, sharpen side edges, detune, wax & buff
Recommend after every 5-10 uses, or before a trip to the mountains
Clean base, wax & buff.
Fully transferrable, 5 full ski or snowboard waxes: Clean base, wax & buff.
New binding mount OR
binding re-mount: remove binding from ski, fill and seal holes, remount binding
* Note: Not all bindings can be remounted on all skis. Also, Snow Rider cannot remount bindings that are no longer indemnified by the manufacturer; bindings that have surpassed their indemnification period will not be accepted for service work. Please ask our staff if unsure.
New binding mount OR
binding re-mount: remove binding from ski, fill and seal holes, remount binding
* Note: Not all bindings can be remounted on all skis. Also, Snow Rider cannot remount bindings that are no longer indemnified by the manufacturer; bindings that have surpassed their indemnification period will not be accepted for service work. Please ask our staff if unsure.
Adjust binding to boot, set release value (DIN) to correct position (according to height, weight, skier ability, boot sole length)
* Note: Not all bindings can be adjusted to fit certain boots. Remount may be required in some situations. Not all bindings can be remounted on all skis. Also, Snow Rider cannot remount bindings that are no longer indemnified by the manufacturer; bindings that have surpassed their indemnification period will not be accepted for service work. Please ask our staff if unsure.
This process uses specialized equipment to check the release values of your binding to make sure that they are within a safe operating range. The technician will also check your ski boot/binding interface to ensure proper release and retention functions.
Pass Holder: $55
Non-Pass Holder: $65
Maintenance for boards with base gouges
Clean and stone grind base, P-Tex gouges, ceramic-disk sharpen side and base edges, detune, wax & buff
Pass Holder: $45
Non-Pass Holder: $55
Maintenance for skis in good condition
Clean and stone grind base, ceramic-disk sharpen side and base edges, detune, wax & buff
Pass Holder: $30
Non-Pass Holder: $35
Clean base, sharpen side edges, detune, wax & buff
Recommend after every 5-10 uses, or before a trip to the mountains
Clean base, wax & buff
Fully transferrable, 5 full ski or snowboard waxes: Clean base, wax & buff.
Mount new binding to board
Re-mount old binding
Change Stance
Adjust to boots for correct fit
Due to the efficiency and waste reduction of our Wintersteiger WaxJet, there will be an additional charge for an iron wax. Please inform the technician at the time of drop off if you wish to use this service.
If you require any more information, please call Snow Rider @ 780-434-3991 ext. 249 or visit the Shop located behind Guest Services.
Other Repairs will be handled at the discretion of the technician.
Glue top sheet back on
24 hour drying time required
Sharpen Only: $15
P-tex work: $20
Base Grind / Texturing: $20
The Turnaround time for all equipment is 48 hours.
Pick-up tab must be present in order to pick up equipment.
For Binding Adjustments, binding mounts, and binding inspections you need to bring in ONE boot. Please know the height, weight and skier type for these services.
Snow Rider cannot adjust bindings that are no longer indemnified by the manufacturer; bindings that have surpassed their indemnification period will not be accepted for service work.